I'll contact AMD and asus though, thanks for the help. This current board has some mileage on it, (secondhand from someone else who treated it well) but it shouldn't be too serious. I had a working (but 4 EPU pin) PSU before that worked on my previous motherboard, it did not work on this one. You didn't mention, did the computer EVER run? or is this a new build? Obviously, if you can get it to boot with that PSU then the problem is your PSU. Just need know good power to see if you can get to the BIOS/Boot screen. At this point it doesn't even need to be the same power as the Golden Field. One last thing to try is to hook up a different psu one that is a known good, working unit. I would, as soon as able, contact manufactures. I have just checked the processor pins thoroughly (they're fine) and have done as you said for the thermal paste and there is no change, the same problem persists. However, reviews of it say that it is "all right in non-stressful environments" It's a 650W model. My PSU is the Golden Field ATX-S728 which I got locally but apparently is a PSU bought by a chinese company from other companies then rebranded. It is very rare, but we worked with another forum member this spring and summer and he did EVERYthing trying to track down a problem and finally AMD confirmed a bad CPU and did an RMA. Lastly, at least for now, there is a possibility that the CPU is defective. Can you provide the actual maker and model and the power it is supposed to deliver (Sticker on the side of the psu), please? It could be bad. Who makes that PSU? I have never heard of it. I use Arctic Silver 5, but there are lots of good versions available (see link): Too much TIM can be worse then none at all. The cooler and its bracket will spread the TIM adequately. My suggestion is do Not us as much TIM as is shown and don't spread it just place a drop about the size of a grain of rice in the middle of the CPU and attache the cooler. Follow this guide (with one small change that I will mention) and clean the CPU and cooler and again install with new TIM. but if it is important I will get it out and check I hear it come on when I boot>. Having the CPU fan on or off, plugged or unplugged does not make any difference.ġst, the cpu fan has to be connected or the board may not boot.Ģd Try removing the CPU again, and very carefully check for Any bent pins. Storage: Old 1TB Harddrive Not sure the brand since it is already bolted in. I put thermal grease on the cpu top and spread it evenly across its surface, I don't think I got any on the sides. The GPUs were tested individually without the others seated into any of the PCIe slots.Did you connect the CPU fan and, if you just installed the CPU, did it have thermal interface material (TIM or Thermal grease) on it or did you put some on it? Are any of the fans spinning up? Each of the GPUs that were tested seemed to work fine on account of the fans running when plugged into power. Tried three different GPUs to see if I could get any display from any of them (ATI x1300, Nvidia Quadro 3500fx, AMD R9 270x) Trying the GPU in different PCIe slots (No success) ![]() Re-seating the RAM into different slots (They are currently in the recommended slots for two sticks of RAM Basically this caused the DRAM_LED to flash continuously (never stopped flashing until system was powered off) Pressing the MemOK! button above the DRAM_LED. ![]() Here's a quick list of things that I've tried on my own: The GPU_LED which is slightly worrying me, does not turn on at all. M5A99FX PRO R2.0 Find Another Model By registering your device, you can easily manage your product warranty, get technical. The CPU_LED stays on constantly and is a bright red, I'm unsure if this is supposed to stay that way, but from other articles, I've heard that the LED is supposed to turn off after post. The DRAM LED is under a little black button that says MemOK! which should be important later. On the board there are three LEDs (aside from the SATA led, but that's irrelevant) labeled as GPU_LED, CPU_LED, and DRAM_LED. Once I got around to trying the first boot, I couldn't get any display on my monitor. Hey there guys, so to start off, the other day I bought a new MoBo to replace my old and busted one, after I got home with it I started to put it inside of the chasis and move all of the parts from my old build into it (GPU, CPU, RAM, PSU) and everything was going fine.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |